Before you leave...
Take 10% off your first order
Arrowzoom Car Insulation Foil Roll Product Description & Complete Guide
Arrowzoom Car Insulation Foil Roll is a heat-insulating layer for the insulation of cars. It helps to reduce heat loss and improve noise levels inside the cars.
What Are The Advantages Of Using Car Insulation Mat?
- It has a lower thermal conductivity than other flexible closed-cell thermal insulation materials and has near-zero vapor permeability.
- It provides superior energy-saving performance.
- Aluminum foils reflect approximately 96% of radiant heat and are therefore very well suitable for thermal insulation.
- As a vapor barrier, the film ensures that no water vapor penetrates the insulation material and thus prevents mold formation and moisture damage.
- All-in-one concept that enables fast and simple installation, and trouble-free operation, in a variety of environments.
Features & Highlights of Car Insulation Mat:
✅ Water Vapor Resistance
It is negligible water vapor permanence means no additional vapor barriers or coatings are required.
✅ Green Building Compliant
Made without Ozone destroying agents such as CFCs or HCFCs.
✅ Optimum Thermal Insulation
Made from high quality Foam Rubber and Aluminum Foil, thermally fused to pure reinforced aluminum foil. It can solve tight clearance issues with its very low thermal conductivity.
✅ Appearance & Durability
It provides an appearance and performance that remains unchanged for the life of the building without sagging or giving a quilted look.
✅ Easy To Install & Cut
It contributes to reducing the installation time of mechanical services that may be installed afterward.
✅ Safe To Use
It is completely user-friendly and does not emit fibers or dust during installation or in service. It is non-irritant, odorless, and will not support bacterial growth.
✅ Fire and Smoke Standards
Extensively tested to various international fire and smoke standards.
Before & After Installed Car Insulation Mat
Arrowzoom Insulation Mat Sound Test
Technical Data Sheet
STC (Sound Transmission Class), is a numerical rating of how effective a material is at blocking the transmission of sound through itself. This rating generally applies to hard materials like rubberized sound barriers, concrete, brick and drywall but also applies to a much lesser degree to softer materials like mineral fiber (although it isn’t tested by itself; it’s tested as part of a wall system to verify its effectiveness).
How To Install Insulation Mat Step by Step
Step 1: Clean the Designated Area
Before applying the insulation mat, clean the surface carefully. Please make sure the surface is clean and dry as any dust on the surface will reduce the adhesiveness of the insulation mat.
Step 2: Locate the Insulation Mat for Outline
Lay the insulation mat out for your specific application. Keep in mind that the insulation mat is evenly distributed throughout the surface of the entire surface of the given element.
Step 3: Mark & Resize the Insulation Mat To Best Fit
Measure the designated areas that need to be field cut on the insulation mat and make the appropriate cuts without removing the adhesive paper (examples would be around beams, doorways, or if a short piece is needed). After all the pieces have been field cut, put the material back in the appropriate position on the wall or ceiling and lightly mark the bottom and side of where each piece will be lightly with a pencil to ensure straight application.
Step 4: Hang The Insulation Mat
Slowly peel off the adhesive paper and hang the insulation mat on the designated surface. Once you peel off the sticker, the insulation mat should easily stick to the surface of your choice.
Step 5: Press Evenly To Remove Air Bubbles
Press the mat firmly into place, using a roller for larger pieces. The roller reduces the risk of leaving air pockets, which reduces sound damping capacity. The temperature of the mat and application surface should not be below room temperature during fitting. Heating the material is not necessary.
Can I customize the size of the Car Insulation Mat that I needed?
If you would like to customize the size of the Car insulation mat that you needed, please send an email to us at service@arrowzoom.com.
Technical Specification:
Material:
Rubber + Aluminum Foil
Thickness:
- 7 mm (0.3 in)
- 10 mm (0.4 in)
Size & Dimension:
50 cm x 100 cm (19.7 in X 39.4 in)
- NOTE:
-
We may split your order into multiple shipments for postage. And due to shipping requirements, we compressed (vacuum sealed) the acoustic foam for easy shipping.
-
Please kindly give up until 24 to 48 hours for the foam to restore its normal size.
Returns Policy
Shipping
Purchase over $100 USD or more to get FREE Shipping.
| Order | Tracking | Processing | Shipping |
| Normal | Yes | 1-2 days | 1-2 weeks |
| Express | Yes | 1-2 days | 1 week or less |
Customer Reviews
Based on 3 reviews
Write a review
- Choosing a selection results in a full page refresh.
